Cylinder Hones, Disassembly Benches, Nut Busters®, Shaft Polishers, Tube Washers, and Pump Testers
PRODUCTS
ABOUT US
NUT-BUSTER®
ADDITIONAL TOOLING
For more detail click on picture
 |
MSD-AT: Adjustable tool is supplied with two hardened jaws and can be adjusted from 3” to 9”. This tool can be tightened on cylinders, nuts, heads, glands, or any thing that would require rotation for removal or installation. |
|
|
MSD-CS:
Machinery Service & Design can manufacture any specialty tool
you may need at an affordable price. This socket tool is used on pistons with recessed nuts. The socket can be made to any size and/or configuration mounted to a standard plate that fits our “Nut Buster”. These sockets are made to take the high torques our “Nut Buster” develops. The through hole on our socket tools allows for clearance of the cushion extension found on some cylinders. With the MSD-CS socket tool the need for deep well sockets in the larger sizes is eliminated. |
|
|
STANDARD 1” DRIVE MSD-DP-1
STANDARD 1.5” DRIVE MSD-DP-1.5
|
MSD-DP Drive plates were developed to use your existing drive sockets with our “Nut Buster”. We can furnish these plates with whatever drive size or configuration you request. (Caution – all of our “Nut Busters” will develop torques exceeding manufactures recommended limits for most commercially available sockets.) |
|
 |
MSD-FPS heavy-duty fixed pin spanner tool is designed to be drilled for fixed hardened pins. They can be drilled for two (2) or three (3) pin configurations. The plates come in three standard sizes 2”, 3”, & 3-1/2”.. A 1/8” thick liner protects the shaft from damage upon installation and removal. The plates are Blanchard ground and scribed for easy center locating. |
|
 
|
MSD-LSS-PH Adjustable pin and hook spanner set can be used to remove piston nuts or gland nuts with recessed holes or slots. Pin spanner arms come in sets of three different size pins, ¼”, 3/8” and ½”. Other size pins, metric or SAE, can be manufactured and supplied upon request. All our spanner tools fit our “Nut Buster” for removal of heads and glands.
|
|
 |
MSD-ARC: Adjustable capture for rotation of cylinders. This tool fits our standard MSD-N-20, 30, 40, 50NR and 70 “Nut Busters. It is used to rotate cylinder tubes with clevis ends of widths from 2” to 16”.
|
|
|
|
||
Fixed Brace Tool (For use with pull-apart cylinder set-up and small shaft cylinders) MSD-BT
Adjustable Brace Tool (Recommended for 20k and 30k Nut-Buster) MSD-ABT
Adjustable Brace Tool (Recommended for 40k Nut-Buster) MSD-ABT40 |
MSD-BT
|
Our brace tooling is used as an anchor point when used with our
“Nut Buster” during removing and/or replacing nuts, glands, etc.
The adjustable brace tool captures clevises by using a threaded
shaft to move brace supports tight against the clevis thus reducing
bearing damage and is recommended for high torque nuts and shafts. |
| MSD-ABT | ||
| MSD-ABT40 | ||
|
MSD-HPS: Standard set of 14 plates cut for standard and heavy nuts to fit 2” to 4” shafts. (3” to 6-1/8” nuts). Plates are easily and quickly installed into the capture ring of the “Nut Buster”. They are used as a box wrench to remove and/or tighten nuts and offer a very affordable alternative to large sockets. MSD-HPSM Metric Plates can also be supplied in metric sizes to 155mm. | |
Shown above is a typical set-up to remove nut that is not standard. The nut is captured with the MSD-AT tooling locked into the MSD-N-20 “Nut Buster”. The shaft is supported with a MSD-V non-marring “V” positioned to center height of the “Nut Buster” with a MSD-VE vise elevator. The clevis is secured with a MSD-BT standard brace tool.
Stand out from your competition by having certified people working for you. Check out the Fluid Power Society Web site for information on certification for Hydraulic Specialists, Hydraulic Mechanics and Hydraulic Technicians.
Beginning and Intermediate Fluid Power Training Fluid power courses for IFPS Certification or customized classes for your companies needs. Contact Leslie's Contract Services at sales@fi2m.net or call 414-617-4870 for information
The Equipment Service Association is an association of companies successfully engaged in the sales and service of hydraulically, pneumatically or electrically operated tools, components, and equipment.
Check them out at www.2esa.org
HydraulicRepairShops.com is the place to find hydraulic repair shops and hydraulic repair parts suppliers. Find shops that repair hydraulic cylinders, hydraulic pumps, hydraulic presses, hydraulic lifts, hydraulic motors, hydraulic power units, hydraulic systems, and other hydraulic components. Add Your Hydraulic Repair Shop to the list of companies on this site for a small fee.